You asked: Should I use tongue and groove roof sheathing?

The main reason to use tongue-and-groove boards these days is appearance – from beneath the roof. Say what you want about them but OSB and plywood do not offer a very attractive “finished” look. T&G roof decking, however, looks classy and rich.

Can you use tongue and groove sheathing on a roof?

Roof sheathing and decking for residential, commercial & industrial construction. Eliminate the need for H-clips or blocking. Protect from rain during construction – the T&G interlocks for immediate protection. The EASY T&G ROOF edge profile is designed for easy installation even if slightly bowed.

What is the best material for roof sheathing?

OSB is now the most-used sheathing and subflooring material for new roofs and roof replacements. OSB is currently selling for less than plywood by approximately $3 per sheet, meaning a savings of several hundred dollars per conventional home.

Is tongue and groove better than plywood?

Tongue-and-groove plywood is superior to regular plywood for floor decks because it creates a stronger, more rigid subfloor, and helps eliminate sagging and “bounce” at the seams between the joists. But it is also more difficult to install because the tight-fitting joints don’t always go together easily.

IT IS INTERESTING:  Your question: How do you nail roof rafters?

What is the best thickness for roof sheathing?

The recommended thickness for roof sheathing is ⅝” thick. Sheathing with a thickness of less than that is much more likely to result in bowing between framing which could potentially compromise your exterior roof material.

Is 7/16 OSB OK for roofing?

…or a non-laminated panel, such as this OSB. Either one is acceptable. The typical thickness of roof sheathing is about 7/16-inch, which is just under 1/2-inch. … If you find 3/8-inch plywood installed as roof sheathing, it’s a good idea to make your client aware of its presence.

Does a roof need sheathing?

Your roof sheathing is an important component of your roofing system. Sheathing holds up your shingles, keeps the elements out, and helps distribute weight evenly across your roof.

What is better for roof sheathing OSB or CDX?

CDX and OSB are used for almost similar things, but because they have different features, one is better applied in some tasks and the other one on other tasks. CDX is best for sub-flooring. … OSB also seems to be good for roof sheathing. But take care, it also requires that you use water-resistant coating at the edges.

Should plywood go under metal roof?

For many applications, a layer of plywood underneath your metal roofing is an unnecessary expense. … Boards measuring 1 inches by 4 inches or 2 inches by 4 inches are commonly used for purlins, though never use treated lumber because it will corrode the steel roof and fasteners.

What is the best plywood for roof sheathing?

Builders love plywood for its water resistance, structural stability and low cost. They also love oriented strand board, though. It costs even less and is comparable to plywood on the other two counts, and they increasingly prefer OSB for roof sheathing. Either is an acceptable choice in most jurisdictions.

IT IS INTERESTING:  How do you keep a roof from getting hot?

How tight should tongue and groove be?

All it takes is 1⁄8″. The joint should be a firm press fit: If you have to knock the pieces together, then struggle to pull them apart, the joint’s too tight. A tongue that’s a hair too fat for the groove may actually seat, but it will stress the groove sidewalls and may, in time, prompt them to split.

Why do people have tongue and groove?

Tongue and groove joints allow two flat pieces to be joined strongly together to make a single flat surface. Before plywood became common, tongue and groove boards were also used for sheathing buildings and to construct concrete formwork. A strong joint, the tongue and groove joint is widely used for re-entrant angles.

How far can tongue and groove span?

Fastening: At each support, two-inch decking shall be toenailed through the tongue and face nailed with one nail using 16d common nails. Span: Our Fir & Larch Select Struc can easily span 7′ between supports. Reach out to us and explain your application if you’re trying to achieve a further span.

Is OSB stronger than plywood?

Wood fiber is used more efficiently in osb. Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood.

What thickness OSB for a roof?

The thickness of OSB that you need varies on where it is used in a building. Typically 3/4″(18mm) for floors and 3/8″ (9mm) for walls and 1/2″ (11mm) roof. Also make sure that you get your supporting timbers at the correct spacing.

IT IS INTERESTING:  Why would a brand new roof leak?

How thick should the plywood be for a roof?

Most Common Thickness

The most common rafter spacing is 24 inches, and 5/8-inch plywood is recommended for that. It will support roof loads for most situations and is the standard for most roof applications. Roofs with very heavy loads may require 3/4-inch thickness.

Roofs and roofing