What are the best nails to use for roofing?
Stainless steel nails are good for fastening tiles and slate. Galvanized roofing nails, or steel nails coated in zinc, are perfect for asphalt shingles, and they hold up well against rust. Aluminum nails should be used for surfaces made out of metal and siding.
What size of roofing nails should I use?
NRCA does not recommend the use of staples for fastening asphalt shingles. Roofing nails should be round-headed, sharp-pointed 11-gauge galvanized steel or the equivalent corrosion-resistant roofing nails. Nail head sizes recommended are 3/8-inch to 7/16-inch diameter. Nail heads should be low profile, smooth and flat.
Do you need galvanized nails for roofing?
Roofing nails tend to be galvanized, a process that makes stainless steel resistant to rust by coating it in a layer of zinc, which does not rust. Galvanization is very important when it comes to roofing nails, but even here you need to be careful because there are different types of galvanization.
Which is better roofing nails or staples?
Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier. Staples are far less prone to jamming up in a gun than nails. Staples cost less money.
Can you use aluminum nails for roofing?
Aluminum
Aluminum is a weaker metal than steel and copper. However, aluminum nails are still used on asphalt shingle roofing by some roofers. Aluminum nails are more prone to corrosion, as well as chemical and salt damage, than steel nails.
Can roofing nails be too long?
Yes, they can. If they are too long, they will protrude through the sheathing at the roof overhang and be visible. We call these “shiners.” If they are too long over the rest of the roof, it is unimportant, and they probably have marginally greater holding power.
Do you nail down roll roofing?
In most cases you can simply overlap the sheets at the ridge using roofing cement and nails for the final piece. However if the final piece does not come down at least 8 inches past the peak, cover the peak with a 16-inch-wide strip that is embedded in cement.
Is it better to hand nail shingles?
Some roofers believe hand-nailing shingles gives them more control over the process. They can use “feel” to determine if the nail is deep enough and in the right location. Since hand-nailing takes a bit more time, they have the chance to correct any mistakes on the spot. On the other hand, labor costs will be higher.
Should roofing nails be exposed in attic?
Yes, and there are two types of nails that are normal to see in an attic: 1) The ring-shank nails used to secure asphalt shingles to the plywood or OSB roof sheathing typically penetrate into the attic 1/4” or more.
Are stainless roofing nails worth it?
Since they’re stronger, nails made of stainless steel are sometimes preferred for fastening harder roof tiles like slate and ceramic. Overall, stainless is a good but not great nailing option for your roof. Better than aluminum, but not as great as the next choice…
How long do Galvanised nails last?
A key benefit of using Hot Dip Galvanizing is its durability. Data shows that galvanizing can provide between 34 to 170 years of protection for steel.
Do Galvanised nails rust?
Galvanised nails have undergone a galvanisation process which involves covering them in order to form a protective barrier making them highly resistant to rust and corrosion, and the ideal product for outdoor uses.
Can you use brad nails for roofing?
Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. … For woodworking projects, a brad nailer is a good choice. If you’re constructing a fence, a framing nailer is a good option.
When did roofers stop using staples?
While it used to be common practice to use staples to attach asphalt shingles to a roof, this has been a prohibited method of attachment in Minnesota since 2003. Today, staples are considered an inferior method of attaching shingles to a roof, but it’s easy to understand why roofers like staples.
Can I use staples for roofing felt?
Tack the roofing felt down with 1/4″ staples using an air compressor with a pneumatic stapler, a hammer-tacker, or a staple gun every 12 inches.