Question: What kind of nail gun do I need for cedar shingles?

“The CSSB favors the use of aluminum/stainless steel nails for cedar shingles. However, if you’d rather use staples, go for stainless steel staples Type 316 in sites within 15 (fifteen) miles of salty water. Use Type 304/Type 316 for locations further from the defined salt water zone”.

What kind of nails do you use for cedar shingles?

Ideal nails to use on cedar wood are made from aluminum, double-dipped galvanized, or stainless steel. Other types of nails such as plain steel nails are not advisable because reactions between the nails and the siding and the environment will create ugly stains on your siding over time.

Can you use a finish nailer for shingles?

Small-body nail guns include brad nailers, finish nailers and crown staplers. … These nailers are used for more technical projects such as framing out a basement or installing roofing shingles.

Where do you staple cedar shingles?

Use 2 fasteners per shingle at about 3/4” (1.9 cm) from each edge, and at 1” (2.5 cm) above the butt-line of the overlapping shingle. If shingles are wider than 8” (20.3 cm), use 2 additional fasteners driven 1” (2.5 cm) apart near the center of the shingles.

IT IS INTERESTING:  What does a roof shingle blister look like?

Can you use a brad nailer for cedar shingles?

A regular brad nailer? … That will make our task easy as we will only need to identify a nail gun that shoots the accepted nails.. Now, here is what the CSSB says about fasteners for cedar shingles: “Use either rust-resistant staples or shingle nails (1-1/4” to 1-1/2” long), galvanized, in stainless steel or aluminum”.

Can you use a nail gun on cedar siding?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.

What goes under cedar shingles?

Cedar Breather® is the solution for preserving the beauty and life of wood roofing. As an underlayment for wood shingles and shakes, Cedar Breather provides space for a continuous air flow between the solid roof deck and the cedar shingles.

Where do you nail cedar shakes?

When it comes to the actual installation of the shakes, you want to avoid using a nail gun completely. Instead, you should install each shake by hand, ensuring you use two nails that are four inches from the top of the shake, and one inch from the sides.

How much does cedar shake reveal?

The maximum recommended exposure for cedar shingle siding is 1/2 inch less than one-half its length. For example, a 16 inch cedar shingle has an exposure of 7 1/2 inches; an 18 inch shingle has an exposure of 8 1/2 inches, etc.

What is the difference between a framing nailer and a roofing nailer?

Answer: Most framing nailers have a minimum fastener (nail) length of 2″. Whereas, roofing nails are typically 1 1/4″. … Siding nails require a smaller head than roofing nails, so you’ll have to check with your local building center to see what’s available for the roofing nailer you’re going to use.

IT IS INTERESTING:  How much does a square of roof tile weight?

Is a brad nailer the same as a nail gun?

The brad nailer is designed to shoot 18-gauge nails whereas the finish nail guns are either for 16-gauge or 15-gauge nails.

What nails do you use for shingles?

What Type of Nails Should be Used with Shingles? For best performance, you should use ring roofing nails that are made of hot‐dipped galvanized steel. You should use 12-gauge or thicker. The length of nail you use depends on the thickness of the sheathing and shingles you use.

Is it better to nail or staple shingles?

Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. … If staples are properly installed, they offer nearly the same wind resistance as nails. The problem with staples is the orientation of the staple crown.

Can I staple cedar shingles?

The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone – stainless steel staples Type 304 or Type 316 must be used.

How many staples are in a square of cedar shingles?

The bottom course should extend at least 1” (2.5 cm) from the top of the foundation or eaves. Use 2 fasteners per shingle at about 3/4” (1.9 cm) from each edge, and at 1” (2.5 cm) above the butt-line of the overlapping shingle.

IT IS INTERESTING:  Question: Why are roofs pitched at acute angles?
Roofs and roofing