Is EPDM roofing any good?

Even with a seam, EPDM is virtually waterproof, and if a leak ever does develop, repairs are fast, easy and inexpensive. Not only that, EPDM roofs are fire resistant. They are almost impossible to ignite, and they can actually impede the progress of a fire. An EPDM roof lasts a long time.

How long will an EPDM roof last?

EPDM roof membranes remain stable over time and can have a life expectancy of over 50 years.

Which is better TPO or EPDM?

TPO has better dimensional stability than EPDM. EPDM is more likely to shrink which can cause a variety of problems on your roof.

Is EPDM good for flat roofs?

EPDM rubber roofing is the obvious alternative to traditional felt, bitumen or asphalt for installing on flat roofs and extensions. … The biggest benefit of using this type of roofing for your flat roofs is that our ClassicBond EPDM rubber roof membranes have a proven 50+ year life expectancy.

How good are EPDM roofs?

As you can see after going through our list, EPDM rubber roofing has more benefits than most other roofing methods. It is a strong, durable and resistant material which is easy to repair should damage happen.

IT IS INTERESTING:  Quick Answer: Does a roof warranty cover leaks?

Can you walk on EPDM roof?

Yes to an extent. EPDM is designed to take LIGHT foot traffic during installation and for occasional cleaning or maintenance. If you require more use than this, i.e. for a balcony then there are additional materials that can be laid over your EPDM for a more durable solution.

Does EPDM have to be glued down?

When you are fitting an EPDM roof, you need to make sure that it is glued down properly. During the membrane application process, you will need to apply two different types of adhesive. The first is a water-based adhesive. Use Permaroof deck adhesive for the best results.

How much does it cost to install EPDM roof?

The Cost of an EPDM Roof

If you decide to go with an EPDM roof installation, you should expect to pay somewhere between $4 to $8 per square foot which works out to be about $6,000 to $12,000 for 1,500 square feet of roof.

Can I put EPDM over felt?

Do not try to lay EPDM over felt. Felt if in good order, free of dirt, dry, needs to be primed with FG35 primer (produced by Carlisle Industries).

Can EPDM be heat welded?

Yes! The membrane can be joined and sealed by using a hot air gun with a flat nozzle and seam roller to creat a heat weld.

Is EPDM roofing expensive?

EPDM rubber roofing cost

This type of rubber roofing can be a great choice with its durability and other features. It may be a little more costly than other types of roofing but is more than worth the cost. The average EPDM rubber roofing cost is £70 per square metre.

IT IS INTERESTING:  Question: How tall is the average house roof?

Is EPDM better than felt?

Rubber roofing like EPDM is considered a far superior product than traditional felt thanks to the wide range of benefits on offer. It’s one of the highest quality materials for flat roofs and is incredibly easy to install. The result is a robust, waterproof and durable roof that won’t tear, rot or blister.

What is the best roofing material for a low pitch roof?

Rubber roofs are a top choice for flat or low pitched roofing as it adheres to the roofing materials below it and, when installed correctly, provides a watertight seal to the elements. Choosing the best low slope roof materials often comes down to weighing the pros and cons based on your home and your needs.

How do you maintain EPDM roofing?

Regular cleaning is required to maintain the EPDM surface, and consistent washes ensure resistance from heat cracking. When conducting routine rubber roofing cleans and check-ups, sweep away any excess leaves, sticks or material resting upon the rooftop.

How thick is EPDM roofing?

EPDM membrane is manufactured in various thicknesses (. 045″ to . 090″ thick) and is available as a non-reinforced or reinforced sheet (depending upon application). Other thicknesses are also available for use in non-roofing applications as a special order.

Can EPDM be installed on plywood?

EPDM should be bonded over 5/8″ plywood, 5/8″ OSB board, or polyisocyanurate board with a fiberglass backing.

Roofs and roofing