How many nails do you need for shingles?

In most cases, 4 nails are adequate. Position the nails appropriately according to the shingle installation instructions. Align shingles properly to avoid nail exposure.

How many nails do you put in a shingle?

Each shingle should be held by four nails. Six nails are preferred for areas that experience wind.

Where should nails be placed on shingles?

Use 4 nails per shingle placed 6-1/8″ above the butt edge, 1″ and 13″ in from each end and 1/2″ above each cutout. Drive nails straight so that nail head is flush with, but not cutting into shingle surface.

How long should your nails be for shingles?

Proper Nail Application For Asphalt Shingles

Nails should have a minimum, nominal shank diameter of 11- or 12-gauge, and a minimum head diameter of three-eighths of an inch. The length of each nail must be a minimum of 1¼ inches long, and for roof-overs, Atlas recommends a nail length of at least 2 inches.

IT IS INTERESTING:  Quick Answer: Can you paint a tar roof?

What kind of nails do you use for shingles?

What Type of Nails Should be Used with Shingles? For best performance, you should use ring roofing nails that are made of hot‐dipped galvanized steel. You should use 12-gauge or thicker. The length of nail you use depends on the thickness of the sheathing and shingles you use.

Is it better to nail or staple shingles?

Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. … If staples are properly installed, they offer nearly the same wind resistance as nails. The problem with staples is the orientation of the staple crown.

Can you nail into shingles?

Yes, professional roofers use nails to apply shingles, but they do so in a very specific way so that each nail is covered by the shingle above it. Adding another nail above the shingles compromises your roof system. … A roofing professional will choose corrosion-resistant screws for this job, not just nails.

Can you put shingles on without nails?

A sturdy and stable way to install roll roofing with no nails is by using torch-down roofing. For this type of roofing, you’ll be utilizing a propane torch to apply heat to the layers of roll roofing to fix them firmly into place.

Do you peel the plastic off of shingles?

No. The GAF shingle application instructions for our entire product line specifically state that that film does not need to be removed: NOTE: The film strips on the back of each shingle are to prevent sticking together of the shingles while in the bundle. Their removal is NOT required during application.

IT IS INTERESTING:  Is roof coating like paint?

What size nails should I use for roof sheathing?

Step 3: Fasten Roof Sheathing Panels Properly. Fasten panels with a minimum of 8d Common (0.131-inch by 2-1/2-inch) nails spaced a maximum of 6 inches on center at supported panel ends and edges. At intermediate supports, fasten panels 12 inches on center. In high-wind areas, more fasteners may be required.

What causes nails to pop through shingles?

Nail pops can be caused by a variety of reasons. When the temperature changes, expansion and contraction can cause the nails to pop up and lift the shingles. … Because a nail pop brings the shingle up with it, water penetration under the single can occur, or strong winds can blow the shingle off the work.

Do you nail down roll roofing?

In most cases you can simply overlap the sheets at the ridge using roofing cement and nails for the final piece. However if the final piece does not come down at least 8 inches past the peak, cover the peak with a 16-inch-wide strip that is embedded in cement.

Can you use brad nails for shingles?

Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. … For woodworking projects, a brad nailer is a good choice. If you’re constructing a fence, a framing nailer is a good option.

How many pounds of shingles are in a square of nails?

You will need approximately 2 ¼ pounds of nails to install a square of shingles in regular conditions, and about 3 ½ pounds if you are dealing with windy conditions. Because nails are purchased by the pound, so can ask your supplier for the correct number of nails for your size roof, in the length you specify.

IT IS INTERESTING:  Why was thatched roofed?

Can I use plastic cap nails for shingles?

Carefully pull them and use a roofing nail. For starters, the plastic cap will not seal on the granular surface of a shingle. … They hold up better against rust, and they can also be used for asphalt shingles.

Roofs and roofing