How do I sheath my roof myself?
- Step 1: Check That Rafter Ends Are Level for Nailing Surface. You want to be sure that the rafter ends form a straight line. …
- Step 2: Ventilate the Roof. …
- Step 3: Apply the Roof Sheathing Panels. …
- Step 4: Cover the Roof Sheathing with Shingle Underlayment Felt. …
- Step 5: Install the Roof Shingles.
What is the minimum thickness of plywood for a roof?
Minimum Thickness
Most roofs will be sheathed in plywood at least 3/8 inch thick. That will suffice on a roof with rafters set 16 inches apart with minimal roof loads.
What do you use to sheath a roof?
Oriented Strand Board (OSB) or plywood can be used, although plywood will provide higher nail head pull-through resistance. Use panels rated as “Exposure 1” or better. Install sheathing panels according to the recommendations of the Engineered Wood Association (APA). Use panels no smaller than 4 feet long.
How much overhang should a plywood roof have?
The overhang is multiple meaning that the sheeting you would overhang some 3/4-1″ followed by a drip edge then if using shingles another 1″. If using metal w/o drip another 3/4-1″ past the wood sheeting. You would want to keep your completed overhang close to 1-1/2″ if using gutter.
Should plywood go under metal roof?
For many applications, a layer of plywood underneath your metal roofing is an unnecessary expense. … Boards measuring 1 inches by 4 inches or 2 inches by 4 inches are commonly used for purlins, though never use treated lumber because it will corrode the steel roof and fasteners.
Should I use OSB or plywood for roof?
OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
How much is a sheet of plywood for roofing?
Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.
Should I nail or screw roof sheathing?
The cheapest and easiest is to re-nail or, better yet, screw down the sheathing when you replace your roof covering. The other approach is applying an AFG-01 rated adhesive to enable the roof sheathing to withstand pressure to 250 pounds per square foot or greater.
What size plywood is used on a roof?
Plywood Thickness for Roofing
The thickness of the plywood for the roof should be a minimum of 1/2 inch, but 3/8 inch is standard size. Most roofs will be sheathed in plywood at least 3/8 inch thick. Bigger is better.
Can I use 1/2 inch plywood for shed roof?
If the shed is for light tools then 1/2 inch pressure treated plywood is acceptable. If the shed is for heavier storage, then pressure treated 3/4 inch exterior-grade CDX plywood is the best.
What type of plywood is used on roofs?
CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes). The wood is graded on each side from A to D, depending on the level of imperfections, (A being free of all imperfections and knots and D being un-sanded and considerably defected).
How much does it cost to sheath a roof?
The thicker the plywood your roofer uses, the more expensive the job will be. Your price could vary depending on how much the roofing company charges for labor, but generally you can expect to spend between $70 to $100 for each sheet of plywood.
How long does roof plywood last?
How long does roof plywood last? As plywood lasts about 30 to 40 years and we run the risk of delamination and required replacement in a few years.
Can plywood roof sheathing wet?
A: It is never a good idea to install a roof over wet plywood or any type of roof sheathing. Trapped water will boil when the sun heats the roof and the shingles will then have small pits where the steam finally escapes.