Do you nail or staple roofing felt?
Some roofers prefer to attach felt underlayment with 1-inch roofing nails or special nails with plastic washers, but most codes allow staples, which are easier to drive.
What do you stick roofing felt down with?
Bostik Bituminous Felt Adhesive for Roofs is a cold applied adhesive for bonding bituminous roofing felts to asphalt, felt, metal and concrete.
Which way does roofing felt go?
Roofing felt has a smooth side and a rough side; the side that needs to face the elements is the rough side. Should the nails go straight through the shed roof and be visible on the inside, from where the felt has been nailed on? No.
Do you nail down roll roofing?
In most cases you can simply overlap the sheets at the ridge using roofing cement and nails for the final piece. However if the final piece does not come down at least 8 inches past the peak, cover the peak with a 16-inch-wide strip that is embedded in cement.
Do I need adhesive for shed roof felt?
When felting a roof shed, you will need enough felt to cover the roof as well as felt adhesive and plenty of galvanised clout nails In addition, you will need a claw hammer, a pry bar, a brush for the adhesive, a knife with a hooked blade, and a spade if you are removing heat-bonded felt.
Is it OK to staple roofing felt?
Roll out about 10 feet of felt and fasten with staples or roofing nails with plastic washer heads. Use a construction stapler or a hammer. Put fasteners at least every 8 inches; some suppliers recommend staples about every 4 inches. … Do the other side of the roof the same way, also with an overlap at the peak.
Can you staple down felt?
The reason they want you to use felt nails is to prevent blow offs if left exposed or high wind areas. Staples can be used for tacking it down, but not recommended to hold.
Can you staple felt?
use galv clouts for the lathes or battens and the same for the felt. we tap the nail in so far then clench it over as it grips the felt better in windy conditions. some roofers use a staple gun to tack the felt.
Can you put roofing felt on top of roofing felt?
You can but you would be wasting the felt, ((felt is tar paper installed as moisture barrier between wood and shingles)) and your time. Felt being in between two layers of asphalt shingles would be pointless but it wouldn’t hurt anything so go ahead.
Should I use felt adhesive?
If you do not use too many nails, the bitumen will seal around them. The reason you should use adhesive sparingly is because the bitumen in the shed felt will expand in warm weather and it will contract in cold weather. Not using too much adhesive allows it some give, which prevents it from tearing or cracking.
Can you nail roofing felt?
Lay the first piece of felt
Use galvanised clout nails to nail the first sheet of felt onto the roof. We’d recommend nailing from the centre of the edge of the sheet and working outwards. Leave about 5cm between each nail, and ensure the sheet is pulled tight and sitting in line with the roof.
Can you lay roofing felt vertically?
Since overlaps on felt are minimum 2 inches and side laps are minimum 4 inches…then overlapping your felt 4 inches in a vertical run could, therefore, be ok. … Most commodity felt won’t lay flat no matter what you do with it.
Which side of felt paper goes down?
Direction. When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper’s two sides are noticeably different. One side is somewhat sticky, though don’t expect it to leave a glue-like residue on your hands.
How much should roofing felt overlap?
Roofing felt is required to overlap 2 inches over the lower felt course. The overlapping felt creates a secondary barrier for moisture and wicks water away from the shingles above and the sheathing below. Therefore, a 2-inch overlap provides redundancy at the edges where the barrier is weakest.