What is the wood trim around the roof called?

Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards. …

What is the difference between trim and fascia?

Trim is the material used to encase windows and doors, among other features, on a home’s exterior. Fascia is a horizontal or angled board that encloses the edge or face of the projecting eaves.

What is the wood on a roof called?

The entire roof frame is covered in a thin piece of wood called decking or roof sheathing. Roof sheathing material is usually plywood or oriented strand board (OSB) that is just under half an inch. Decking is supported by the roof frame and the layers of a roof, which we cover below, and all rest on top of the decking.

What is the decorative trim along the eaves called?

cornice – (1) a decorative feature found under the eaves of a roof; (2) projecting ornamental molding hiding joint of a ceiling. or roof, and wall.

IT IS INTERESTING:  How do you preserve roof shingles?

What is a roof rake edge?

Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. … A roof rake edge also serves the important function of preventing water from getting into the fascia, and the underlying roof decking of your home.

What is the trim around a house called?

Casing refers to the trim used around interior or exterior windows and doors. Casing is designed to cover the unfinished gap between walls and door or window frames. It usually spans two or three inches.

Is fascia a trim?

Fascia is a specific type of trim, which is installed just below the roof line. It helps to cover the soffit, and provides a more finished appearance for the roof and eaves of the home. These boards may vary in width, but is generally a slightly wider or thicker version of the same trim used on the rest of the home.

What is the point of a roof called?

Roof Ridge: The roof ridge, or ridge of a roof is the horizontal line running the length of the roof where the two roof planes meet. This intersection creates the highest point on a roof, sometimes referred to as the peak.

What goes on roof before shingles?

Sometimes called roofing felt underlayment, roofing tar paper, or roll roofing, this is a layer of protection installed between the roof deck and the roofing shingles.

What is it called where a roof meets a wall?

A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.

IT IS INTERESTING:  Your question: Can I claim for a leaking roof?

What is decorative wood called?

In woodworking, veneer refers to thin slices of wood and sometimes bark, usually thinner than 3 mm (1/8 inch), that typically are glued onto core panels (typically, wood, particle board or medium-density fiberboard) to produce flat panels such as doors, tops and panels for cabinets, parquet floors and parts of …

How do you determine the pitch of a roof?

The angle, or pitch, of a roof is calculated by the number of inches it rises vertically for every 12 inches it extends horizontally. For example, a roof that rises 6 inches for every 12 inches of horizontal run has a 6-in-12 pitch.

What is fascia board for gutters?

The fascia board is the long wooden board behind the gutters on a house. It connects to the roof rafters, closes off the attic and serves as the mount for gutters. … So, if you have damaged fascia, it is important to have it replaced.

Do you have to replace drip edge when replacing roof?

Drip edge is the metal flashing that’s installed at the edges of the roof to help control the flow of water away from your fascia and other roofing components. The drip edge has to be replaced when you get a new asphalt roof.

Does drip edge go around entire roof?

The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.

IT IS INTERESTING:  How much does a roofer charge a day?

Do I need a drip edge on rake edge?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

Roofs and roofing