Quick Answer: How many nails do you need for a square of shingles?

Generally, you should use four nails per shingle in the field of the roof, and 5 nails per starter shingle. For regular three-tab shingles, this would require 320 nails per square for field shingles.

How many nails are in a box of roofing?

Typical box count is 7,200 nails per box, with 120 per coil.

What size nails should I use for shingles?

NRCA does not recommend the use of staples for fastening asphalt shingles. Roofing nails should be round-headed, sharp-pointed 11-gauge galvanized steel or the equivalent corrosion-resistant roofing nails. Nail head sizes recommended are 3/8-inch to 7/16-inch diameter. Nail heads should be low profile, smooth and flat.

How many nails do you put in each starter shingle?

Each shingle should be held by four nails. Six nails are preferred for areas that experience wind.

How many nails do I need for 30 squares of shingles?

Most shingle manufactures recommend using four nails per shingle on the main area of your roof and five nails per square in the first row of roofing. This adds up to an average of 320 nails or 100 square feet.

IT IS INTERESTING:  Is a black roof energy efficient?

How many boxes of nails are in a square?

Nail Quantity per Square

This amounts to an average of 320 nails per square, or 100 square feet. In high-wind areas, you need five nails per shingle, or 480 nails per square.

Is hand nailing shingles better?

While air gun nailing might seem faster, a well-trained hand nailer can do it almost as fast. The key difference between the two is accuracy. Hand driving nails into shingles allows for the roofer to place the nail on the proper nail line and then drive the nail in.

Is it better to nail or staple shingles?

Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. … If staples are properly installed, they offer nearly the same wind resistance as nails. The problem with staples is the orientation of the staple crown.

Can you use a framing nailer for shingles?

These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. … If you’re constructing a fence, a framing nailer is a good option. Complete even more projects by purchasing nailer kits that offer a variety of nail guns.

Are starter shingles required on rakes?

Starter shingle should be installed around ALL edges of your roof. To meet code, technically it only needs to be installed on the bottom eaves, but there are some big benefits to installing it up the rake edges as well (also known as gable edges).

IT IS INTERESTING:  How long does it take Dicor rubber roof coating to dry?

How much should shingles overhang drip edge?

Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.

How do you calculate starter shingles?

Determine the number of shingles to order for starters by measuring the length of the eaves and rakes, then round up to the nearest foot and divide by three (the length of a shingle).

How many nails do you put in a 3 tab shingle?

NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8″ diameter heads, long enough to penetrate through plywood or 3/4″ into boards. Use 4 nails per shingle placed 6-1/8″ above the butt edge, 1″ and 13″ in from each end and 1/2″ above each cutout.

Can you put shingles on without nails?

A sturdy and stable way to install roll roofing with no nails is by using torch-down roofing. For this type of roofing, you’ll be utilizing a propane torch to apply heat to the layers of roll roofing to fix them firmly into place.

Can you nail into shingles?

Yes, professional roofers use nails to apply shingles, but they do so in a very specific way so that each nail is covered by the shingle above it. Adding another nail above the shingles compromises your roof system. … A roofing professional will choose corrosion-resistant screws for this job, not just nails.

Roofs and roofing