Frequent question: What nails do you use for roofing shingles?

What Type of Nails Should be Used with Shingles? For best performance, you should use ring roofing nails that are made of hot‐dipped galvanized steel. You should use 12-gauge or thicker. The length of nail you use depends on the thickness of the sheathing and shingles you use.

What size nails do you use for shingles?

Fasteners for asphalt shingles shall be galvanized, stainless steel, aluminum or copper roofing nails, minimum 12-gage [0.105 inch (2.67 mm)] shank with a minimum 3/8-inch-diameter (9.5 mm) head, of a length to penetrate through the roofing materials and not less than 3/4 inch (19.1 mm) into the roof sheathing.

Do you need galvanized nails for roofing?

Roofing nails tend to be galvanized, a process that makes stainless steel resistant to rust by coating it in a layer of zinc, which does not rust. Galvanization is very important when it comes to roofing nails, but even here you need to be careful because there are different types of galvanization.

How long should roof shingle nails be?

Proper Nail Application For Asphalt Shingles

IT IS INTERESTING:  Can I add a roof rack to my Honda Pilot?

Nails should have a minimum, nominal shank diameter of 11- or 12-gauge, and a minimum head diameter of three-eighths of an inch. The length of each nail must be a minimum of 1¼ inches long, and for roof-overs, Atlas recommends a nail length of at least 2 inches.

Do you nail down roll roofing?

In most cases you can simply overlap the sheets at the ridge using roofing cement and nails for the final piece. However if the final piece does not come down at least 8 inches past the peak, cover the peak with a 16-inch-wide strip that is embedded in cement.

Is it better to hand nail shingles?

Some roofers believe hand-nailing shingles gives them more control over the process. They can use “feel” to determine if the nail is deep enough and in the right location. Since hand-nailing takes a bit more time, they have the chance to correct any mistakes on the spot. On the other hand, labor costs will be higher.

What are the best nails for roofing?

Stainless steel nails are good for fastening tiles and slate. Galvanized roofing nails, or steel nails coated in zinc, are perfect for asphalt shingles, and they hold up well against rust. Aluminum nails should be used for surfaces made out of metal and siding.

Does Harbor Freight sell roofing nails?

Roofing Nails – Harbor Freight Tools.

Are stainless roofing nails worth it?

Since they’re stronger, nails made of stainless steel are sometimes preferred for fastening harder roof tiles like slate and ceramic. Overall, stainless is a good but not great nailing option for your roof. Better than aluminum, but not as great as the next choice…

IT IS INTERESTING:  Should I buy a house with a bad roof?

Can roofing nails be too long?

Yes, they can. If they are too long, they will protrude through the sheathing at the roof overhang and be visible. We call these “shiners.”

Which is better roofing nails or staples?

Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier. Staples are far less prone to jamming up in a gun than nails. Staples cost less money.

Can you nail into shingles?

Yes, professional roofers use nails to apply shingles, but they do so in a very specific way so that each nail is covered by the shingle above it. Adding another nail above the shingles compromises your roof system. … A roofing professional will choose corrosion-resistant screws for this job, not just nails.

How do you calculate roofing nails?

Divide the entire square footage by 100 to reach the estimated amount of shingles needed. Multiply the estimated amount of shingles by 2 to 2 1/2. The resulting figure is an estimate of the pounds of nails needed.

Should roofing nails be exposed in attic?

Yes, and there are two types of nails that are normal to see in an attic: 1) The ring-shank nails used to secure asphalt shingles to the plywood or OSB roof sheathing typically penetrate into the attic 1/4” or more.

Roofs and roofing